Redgar Valorant Settings

Redgar gear breakdown: what each piece actually changes

Mouse: Pulsar Xlite V3 Es Black at 1000Hz polling. At 1000Hz the mouse reports every 1ms, which is the competitive baseline — stable on any modern CPU with Raw Input Buffer enabled. DPI 100 with sens 0.27 means the in-game multiplier does the fine work while the sensor stays in its clean tracking range.

Display: ASUS ROG PG27AQDM at 2560x1440. Lower resolutions like 1280x960 stretch targets wider and can make heads feel easier to hit, at the cost of peripheral clarity; native 1920x1080 keeps UI and minimap sharpest. Pair this with multithreaded rendering on, V-Sync off, and NVIDIA Reflex on+boost if available — frame latency matters more than texture detail for holding angles.

Supporting gear: Wooting Two HE for movement keys, ZOWIE G-SR-SE Deep Blue under the mouse, and Razer BlackShark V2 Pro Black for footsteps, none of which change eDPI, but all of which change consistency: a familiar pad glide and audible footsteps cut down unforced errors more than any sens tweak. If you copy one thing, copy the eDPI (216), not the brand names.

Redgar crosshair explained: Green no center dot, inner lines (length 4, offset 0), outer lines off, outlines off

Import code: 0;P;c;1;h;0;0t;1;0l;4;0o;0;0a;1;0f;0;1b;0. In plain terms this is a Green no center dot, inner lines (length 4, offset 0), outer lines off, outlines off setup. Small inner-line crosshairs like this reward centered head-height placement — you see more of the target around the lines, which helps one-taps at range. The tradeoff is visibility on bright maps (Icebox snow, Breeze sand): if you lose the lines, switch the color to cyan or green rather than enlarging the gap, which would cost precision.

To try it: copy the code above, then in Valorant go to Settings → Crosshair → Import Profile Code, paste, and test in the Range against strafing bots before taking it into ranked. Full per-background preview lives on the crosshair preview page.

Redgar vs other pros: same game, different mousepad math

Redgar at 216 eDPI is 64 points below the pro average (280). As a low-sensitivity arm aimer, Redgar needs roughly 14.2 cm per 360° turn — plan mousepad space around that number, not around anyone else's brand of mouse.

Reading the table: lower eDPI favors calm angle-holding and spray control; higher eDPI favors entry swings and fast clears. None is "best" — pick the row whose turn-distance fits your desk, then use the converter at the top to match it on your own DPI.

How to copy Redgar's settings without ruining your aim

1. Match eDPI first. Enter your DPI in the converter above and set the sens it gives you — that reproduces Redgar's turn-distance exactly.
2. Keep your old crosshair for one session if Redgar's lines feel alien; change sens and crosshair on different days so you know which change helped.
3. Set scoped sens to 1 only if you play the same scoped weapons; otherwise leave yours — scoped multipliers are personal.
4. Give it 3–5 ranked games, then adjust in 5–10% steps. One bad deathmatch is not data.

Data on this page is compiled from public pro-settings listings and community-verified corrections (see Suggest an edit above — 3 matching votes auto-updates a field). Last reviewed against our settings snapshot; if a value changed on stream, submit the correction and it ships after review. Source listing on ProSettings.net ↗

Redgar settings FAQ

What sensitivity does Redgar use?

Redgar plays on 100 DPI with 0.27 sens — eDPI 216, scoped 1.

What is Redgar's crosshair code?

0;P;c;1;h;0;0t;1;0l;4;0o;0;0a;1;0f;0;1b;0 (Green no center dot, inner lines (length 4, offset 0), outer lines off, outlines off).

What mouse does Redgar use?

Pulsar Xlite V3 Es Black Polling rate 1000Hz.

Should I copy Redgar's eDPI of 216?

Only if the turn-distance fits your space: about 14.2 cm per 360°. Match eDPI with the converter, test 3–5 games, then tune ±10%.